Shopping Global,One World One Price

USD
Write a Review
Rating
  • 2022-04-28
    Da****on
    It works for what I bought it for.
  • 2022-04-14
    Jo****as
    Made changing the fan clutch on my dodge ram a breeze. Just get a cheater bar and an 18 - 24 crescent and it takes about 2 minutes to break it loose and spin it off.
  • 2022-04-12
    Ti****tt
    good and strong, very adjustable.
  • 2022-04-09
    M****n
    Works great except the pin dimensions listed are wrong. The small pins actually measure 0.265 (that .005 difference caused a problem for me) and the large pins actually measure 0.345 , not the 0.38 they show. Other than that, these are very sturdy and easy to use. I've been driving this wrench with a hammer to free corroded threads and the wrench is still going strong.
  • 2022-04-05
    Ke****dt
    Works great 👍
  • 2022-03-26
    S****S
    Great tool to have around the house if you ever repair your appliances or garden equipment - especially when you are trying to remove bolt or nut on a shaft with a flywheel. I used the screwdriver method and failed miserably, and I ended up buying this. I was very skeptical at first, but it worked like a charm.
  • 2022-03-20
    Ri****ix
    Good value. Works well on a few test runs but haven't used it on what i intended it for as of yet
  • 2022-03-07
    Ta****er
    Great tool
  • 2022-02-22
    E****n
    I needed to remove the fan clutch assembly from a 2012 Ram 1500. Chrysler products have the fan clutch screwed onto the threaded end of the water pump shaft with one large (36mm, I think) nut. You need a way to hold the water pump pulley so it doesn't spin to break the fan clutch free. There are 5/16ths inch holes drilled in the pulley face at the 3, 6, 9, and 12 o'clock positions.Using the small pins on this spanner, adjust it so the pins fit in the holes at the 3 and 9 o'clock positions. I used a 15 inch Crescent wrench on the fan clutch nut. Held the spanner in place with one hand and tapped the Crescent wrench with a 3 pound hammer. Two taps and it was free. Nice.So much better than trying to rig a homemade tool. I won't use it very often (I hope) but it's nice to have when I need it.
  • 2022-02-22
    E****n
    I needed to remove the fan clutch assembly from a 2012 Ram 1500. Chrysler products have the fan clutch screwed onto the threaded end of the water pump shaft with one large (36mm, I think) nut. You need a way to hold the water pump pulley so it doesn't spin to break the fan clutch free. There are 5/6ths inch holes drilled in the pulley face at the 3, 6, 9, and 12 o'clock positions.Using the small pins on this spanner, adjust it so the pins fit in the holes at the 3 and 9 o'clock positions. I used a 15 inch Crescent wrench on the fan clutch nut. Held the spanner in place with one hand and tapped the Crescent wrench with a 3 pound hammer. Two taps and it was free. Nice.So much better than trying to rig a homemade tool. I won't use it very often (I hope) but it's nice to have when I need it.
  • 2022-02-19
    D****G
    rotor holding tool has two sided use !!
  • 2022-02-19
    da****up
    rotor holding tool has two sided use !!
  • 2022-02-10
    S****J
    Shipping, tool and price were good. Had the right tool when other vendors did not.
  • 2022-02-06
    K****n
    More beefy than I expected for the price. Works well and I don't expect that it will bend or break.
  • 2022-01-04
    Ef****ga
    Su manufactura muy robusto.
  • 2021-12-29
    Ha****er
    This tool built stronger than expected. The metal arms are nearly 6mm thick. The handle is knurled and is 15.5mm in diameter. I'm using it to hold the flywheel on my vintage motorcycles during points adjustments, etc.
  • 2021-12-29
    Ha****er
    This tool built stronger than expected. The metal arms are nearly 6mm thick. The handle is knurled and is 15.5mm in diameter. I'm using it to hold the flywheel on my vintage motorcycles during points adjustments, etc.
  • 2021-12-25
    Da****ro
    fast shipping good quality tool did the job
  • 2021-12-24
    Am****er
    Purchased this to help loosen a fan blade assembly while changing a water pump. Used this with a 3 ft section of pipe and it came right off.
  • 2021-12-18
    p****l
    This tools makes water pumps and clutch fans a breeze
1 2 3 ... 11 12